DD search coil · Minelab X-Terra, two-frequency 3 and 7.5 kHz
NEL Hunter for Minelab X-Terra (all models) · 3, 7.5 kHz
Performance ratings
Specifications
- Size
- 12.5" × 8.5"31.7 × 22 cm
- Weight
- 17.6 oz500 g
- Coil type
- DD3, 7.5 kHz
- Waterproof
- 100%
*Weight is given without the coil cover. Weight may vary slightly depending on the metal detector model. The coil can be used without the plastic cover.
Overview
Made for ground heavily littered with iron.
An exclusive NEL product: this is the two-frequency version, with switchable frequencies of 3 kHz and 7.5 kHz. Switching the frequency lets you set up the metal detector for different search conditions: the low 3 kHz frequency for large and deep targets, and 7.5 kHz as an all-round setting.
It is extremely light for its size, only 500 g, and agile. It is highly sensitive to large, medium and especially small targets on trashy sites: recently abandoned settlements, beaches and parks. Recommended as a replacement for the stock coil.
+5–30% depth+25–50% ground coveragevs. stock coil (depending on the metal detector model)
Compatible Minelab metal detectors
- X-Terra 30
- X-Terra 34
- X-Terra 305
- X-Terra 50
- X-Terra 54
- X-Terra 505
- X-Terra 70
- X-Terra 74
- X-Terra 705
Important for Minelab X-Terra
How do I set the ground balance?
Use automatic ground balance. On X-Terra 50, 54, 505, 30, 34 and 305 you can also use manual ground balance. If the detector will not balance, reduce the sensitivity by 50%.
Which Noise Cancel setting should I use?
- Set it to 0 by default.
- For the longest reach on a large copper coin in air, set it to +1. This may cause false signals from the ground.
- To minimise the response to hot rocks or heavily mineralised ground, set it to −1 or −2. Change the value until the detector stops reacting to such ground.
How do I switch the frequency?
Switch the detector off and on again within 2 seconds: the coil moves to the next frequency. If more than 2 seconds pass between off and on, the frequency stays the same, as the coil remembers the last frequency selected.
- Where it works best
- Sites with a lot of iron in the ground: lost villages and farmsteads, old estates, former fairgrounds, beaches and parks. Its agility and sensitivity to small targets let you pick coins out between iron where a large coil can't single out a good target among the iron.
- Recommended for
- Beginners and experienced detectorists.
Features
The coil is fully waterproof and submersible. The body is filled with epoxy resin and finished with a black marine-grade coating, the kind used on yachts and boats, so it can be used without a plastic coil cover. It handles medium and high ground mineralization well.
Cable strain relief
Protects the cable from kinking and also provides complete waterproofing.
Robust mounting bracket
Holds the coil firmly on the stem.
Outer shell
Made of impact-resistant, UV-resistant plastic.
Coil cover
Protects the search coil from damage and chipping.
Wear-resistant coating
Made of composite materials, so the coil can safely be used without a cover if required.
Rubber rings
For a firmer fit of the coil on the lower stem.
Connector
Gold- or silver-plated contacts.
High-strength cable
With a larger conductor cross-section. Made in Germany.
Protective cap
Protects the connector from dirt and dust.
Fixing bolt and hook-and-loop strap
Supplied with the coil.
Every NEL coil is field-tested for detection depth before sale.
2-year warrantyfrom the date of purchaseAll NEL coils for Minelab X-Terra, two-frequency 3 and 7.5 kHz
Fit X-Terra (all models) · 3, 7.5 kHz. 6 coils available.
